Most of what makes a house work ends up hidden behind drywall. MEP rough-in is the stage when the heating and cooling, wiring, and plumbing go into the open framing, and it goes best when every installer walks into a house that is already laid out. Before any of them arrive, we mark the whole plan on the floor and the studs.
Here is what we mark, what each color means, and why that layout matters to you as the homeowner long after the walls are painted.
MEP rough-in happens before the walls close
MEP stands for mechanical, electrical, and plumbing. Mechanical covers heating, cooling, and ventilation. Electrical covers the wiring, receptacles, switches, and lighting. Plumbing covers the water lines and drains, and on our builds the plumbers run the gas lines too.
Rough-in is when those systems go into the framing, before insulation and drywall. It comes right after framing in the stages of a custom build, and it is one of the busiest stretches of the whole project.
It is also a large share of the cost. In the National Association of Home Builders 2024 construction cost study, major system rough-ins made up 19.2 percent of construction cost, second only to interior finishes.
When the rough-in is done, it gets inspected. The International Residential Code requires a rough inspection of plumbing, mechanical, gas, and electrical systems before anything is covered. After that, the walls close, and every line and box stays where it was set.
That makes the layout the part to get right.
We mark the floor in a different color for each trade
Before the installers start, we lay out the house on the floor. Each trade gets its own color, so the plumbing, HVAC, electrical, and gas installers can each find their part of the plan when they walk on site.
In a kitchen, white on the floor marks the lower cabinets. Pink marks the uppers. We bump the line out where the range hood goes, so the hood and the cabinets on each side of it are clear before anything is installed.
Green is electrical. We mark where each receptacle and light goes and note each receptacle's height. A "CT" beside a mark means countertop height, so the electrician mounts that box above the counter instead of at a standard lower height. Countertop receptacles have their own section of the residential code, and the marks keep each one where the plan puts it.
The layout also shows where the range sits, so the plumber knows where to stub up the gas line. At the sink, the drains and water lines come up where the sink base will be.
Then we staple printed cabinet elevations to the wall above the floor marks. An elevation shows the electrician where the upper cabinets will hang, so the wire for under-cabinet lighting comes out at the height that lines up underneath them.
Every trade reads the same plan.
The layout shows you your kitchen at full scale
The markings guide the installers, but they matter most to the homeowner. Standing in the framing, you can see how large the cabinets will be, where the uppers and lowers go, where the island sits, and where the sink, range, and ovens will land. That sense of scale is hard to get from a drawing.
At this stage, there is still room to adjust. If a run of cabinets feels tight or a walkway does not flow the way you pictured it, we can move a line on the floor. Once the permanent work begins, that same change gets much harder.
Most of these decisions start in the planning phase of your build. The layout is the first time you see them at full size.
We do this on all of our new builds. When the rough-in wraps up, we walk the house with the homeowners one more time to make sure everything is where they want it. Then we move on to insulation.
A clear layout cuts mistakes, callbacks, and cost
A marked layout cuts down on questions. Installers do not have to stop and call for clarification, and they do not have to guess. Our quality control is better, the work is more accurate, and each trade moves through the house more efficiently.
The marks keep working after rough-in. We mark every stud throughout the house. When the drywall goes up, those marks keep the sheets aligned. The receptacle marks also show where a box sits behind the board, so nothing gets covered up by mistake.
Fewer mistakes mean fewer callbacks and fewer changes. That keeps the build moving, and it saves the homeowner money. It follows the same thinking behind how we handle your budget: clear decisions early keep surprises out of the project later.
Most of it ends up behind the walls. All of it starts on the floor.